NetXpertXG

ATEVA Technologie : NetXpert

Test your Ethernet cable. Prove the speed limit.

ATEVA Technologie : NetXpert

Wireless access point speeds at the end of the network are out-pacing the speeds of the installed cabling in the middle of the network. Is it possible that your installed cabling will handle speeds beyond design spec and will keep up with speeds of the new wireless access points? Is it possible to leave your CAT 5e and CAT 6 cables in place, and achieve 1Gbit/sec speeds?  10Gbits/sec speeds?

To find out, with the single press of a button, three key tests are run with the NetXpert XG. In one click, NetXpert XG performs a live speed test sending 1Gb/s through your cable (BERT), and will prove if the cable will perform beyond design spec and keep pace with the speed of newly installed access points.

NetXpert XG is the only cable tester and active network manager to perform BERT (bit error rate test), SNR (signal-to-noise ratio), and delay skew to 1G, 5G, or 10G speeds at the press of a button. Now you can perform real-time bit throughput tests to see if your installed cables will run up to 10Gb.

 

One touch bit error rate test, signal-to-noise ratio, and delay skew

By performing a Bit Error Rate Test (BERT) and standards based tests as per IEEE 802.3an, the NetXpert XG proves the error-free data transmission up to 10Gb/s.

A one touch auto test includes BERT, signal-to-noise ratio (SNR), and delay skew, all of which can impact Gigabit transmission.

Signal-to-noise ratio checks to ensure noise is low enough and signal is high enough for reliable transmission.  Delay skew indicates the signal time delay between the wire pairs. Excessive delay from one pair can result in a serious degradation of transmission performance making it impossible for the receiver to interpret the data stream correctly.

All three crucial measurements for determining reliable data transmission are performed at the touch of a button.  When you are ready to test the next cable, hit test again, and NetXpert XG advances automatically to the next cable being tested.  Each test result is automatically stored to a summary report and a detailed report in pdf, csv, or xml format.

The cable qualifier that is defining a new category — the cable project qualifier

If you are a cable installer, network owner, network builder, or system integrator, you’ll be excited to hear that NetXpert XG includes a project editor and auto test generator for up to 1000 cables, and test reports you can keep for your records or leave with your customer.  Once the tests are created, plug in the cable, click test, and NetXpert XG starts testing the cable to IEEE 802.3 standards to prove the speed of your cable.  Not only do you get a wiremap and cable length, NetXpert XG tests BERT, SNR, Delay Skew, distance to opens, shorts, or miswires.  As a bonus you get active network tests for copper, fiber, and wireless.  And, with 2 NetXpert XG local units, you can test fiber cables.

Cable Project Qualifier

  • Use the project editor, cable test editor, test label editor to pre-configure your cable testing projects
  • Press test to automatically sequence up to 1000 cable tests from the local or remote device to increase cable testing efficiency when working alone
  • Test data cabling for IEEE 802.3 compliance at data rates up to 10 Gb/s (BERT)
  • Determine signal-to-noise ratio (SNR) for compliance up to 10 Gb/s
  • Measure delay skew for compliance up to 10Gb/s
  • Measure length of cable with TDR and capacitance measurements for highly accurate test results and easier troubleshooting
  • Full-color wire map shows distance to open, distance to short, miswires, split pairs, and shield on a color graphical display
  • Save test results and generate standards-based measurement reports providing “Pass/Fail” indication in pdf, csv, or xml format

Perform active network management

  • Support for IPv4 and IPv6
  • Discover your network and see the connected network devices
  • Identifies defective PoE switches with a PoE load test
  • DHCP test
  • Ping lists can be defined and saved for later use
  • LLDP/CDP detection and analysis
  • Identifies VLANs present in your network
  • Data transfer from the tester to the PC using USB stick, wireless, or bluetooth connectivity
Length Measurement Technology Time-Domain Reflectometry (TDR) and capacitance
Cable Measurements Cable Testing and ID: up to 1,000 ft (305 m)
Split Pair Detection: 3 ft (1 m) to 1,000 ft (305 m)
Length Measurement: 0 to 1,500 ft (457 m), ± (5%+1ft (30 cm))
Distance to fault: 0 to 656 ft (200 m) ± (5% + 3ft (1m))
Supports 8 wiremap remotes (RJ 45) and 24 RJ-45 ID only
remotes
Power over Ethernet (PoE) Test supports IEEE 802.3af PoE (Type 1, max 15.4W),
IEEE 802.3at PoE+ (Type 2, 30W) and 802.3bt PoE++ (Type 3, 60W)
Future proofed for IEEE 802.3bt Type 4 100W higherpower PoE
Active Ethernet Network and test support by interface:
Copper RJ-45 interface –100/1,000/2,500/5,000/10,000 Mb/sec link speeds
Fiber SFP+ #1 interface supports 10Gb/sec link speed
Fiber SFP+ #2 interface supports 1Gb/sec link speed
WiFi 802.11 a/b/g/n 2.4 Ghz WiFi and Bluetooth
Maximum Voltages Maximum voltage that can be applied to any 2 connector pins without causing damage to the tester:
RJ-45: 60 VDC or 50 VAC
Save Test Results Stores virtually unlimited cable or network tests with user defined names per project
Tone Generation Tone Frequencies: 730 Hz and 1440 Hz
Languages English, German, French, Spanish
Battery Li-Ion, 7.2 VDC, 3.1A-hr (typical)
Battery Life at 10Gb: 5 hrs minimum, 24 hrs stand-by
Temperature Operating: 14 to 140° F (-10 to 60°C)
Storage: -22 to 158°F (-30 to 70°)
Humidity 10 to 90% non-condensing
Enclosure Injection molded plastic
Display 7″ Color TFT-LCD capacitive touch display,
1024 x 600 resolution (WSVGA)
Size 245 x 177 x 73 mm (main unit)
130 x 177 x 55 mm (Active Remote)
Weight with Battery 2.6lbs (1.2 kg) main unit
1.3lbs (0.6 kg) Active Remote

datacheck analyzer software product bundle for mobile industrial ethernet diagnostics

Analyzer IE & Analyzer PRO

Software for Mobile Diagnostics and Acceptance Testing of Industrial Networks

Analyzer IE / PRO is a comprehensive software solution for acceptance testing and efficient troubleshooting of Ethernet-based industrial communication. In a PROFINET environment, the mobile diagnostic tool generates standardized acceptance reports in accordance with the recommendations of PROFIBUS & PROFINET International (PI), making it an easy-to-use product that is tailored to the needs of plant suppliers, maintenance personnel as well as service providers.

This product belongs to our PROFINET Diagnostics family. In order to view our expertise and the complete list of products please Download the PROFINET Diagnostics Brochure.

Comprehensive Functionality

  • Diagnostics list, error statistics, network statistics
  • Enhanced flexibility by supporting online as well as offline mode
  • Generation, analysis and handling of diagnostic data such as graphical topology, inventory list and reference measurements, also for standard Ethernet components (eg PCs, camera systems)

Automated Generation of Acceptance Test Documents

  • Time saving by automatically created test reports
  • Flexible definition of acceptance criteria
  • Transparent reporting by following PI guidelines

Tool Addressing Complete Plant Lifecycle

  • Data on network configuration, network communication and diagnostic messages
  • Error identification for effective troubleshooting (e.g. based on inventory list of network devices)
  • Chance to support exchange of general project information between end users, EPC contractors, system integrators and maintenance service providers
  • Seamless integration with Softing diagnostics per-manent monitoring solutions TH SCOPE and TH LINK
Technical Data
Functionality
  • Analysis of device logs
  • Live list, statistics, inventory
  • Topology and trend analysis
  • GSDML file support, plaintext messages in diagnostic list
  • Acceptance measurements and acceptance reports
  • Reference comparison
  • Configurable time intervals for automated export of inventory and topology data
  • Data export via Excel
  • Configurable Blacklist feature for robust operation
  • Optional (Analyzer PRO): Telegram analysis: jitter, refresh interval, load ratio
Supported Protocols PROFINET, EtherNet/IP, Modbus TCP
Interfaces
  • SNMP Agent
  • OPC UA Server
System Requirements Adobe Reader 8 or higher for reading the documentation and for printing the topology
Supported Operating Systems Windows 7, Windows 8.1, Windows 10
Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Network Access Data collection through TH LINK PC (PROFINET, EtherNet/IP, Modbus TCP)
Demo Version Full TH SCOPE functionality can be used for free for 30 days after installation
Licensing Software or hardware key
Scope of Delivery
Software Analyzer IE
License Software key (bound to PC) or hardware key
Hardware profiTap: Network tap for telegram analysis operation, optional (Analyzer PRO)
Documentation Installation manual, user manual, release note
Order Numbers
LRA-JY-003041 Analyzer IE (software key)
LRL-JY-003042 Analyzer IE (hardware key)
KPL-JY-003043 Analyzer PRO
Additional Products and Services
GEA-JN-003006 TH LINK PROFIBUS
GDA-JA-003034 TH LINK PROFINET
GDA-JY-003037 TH LINK Industrial Ethernet
LRA-JY-003028 TH LINK PC Industrial Ethernet
TRA-PB-TECH Training “PROFIBUS Technology”
TRA-PB-TS Training “PROFIBUS Troubleshooting with exam to Certified PROFIBUS Installer”
TRA-PN-CERTINST Training “PROFINET Acceptance and Commissioning”
TRA-PN-CERTENG Training “PROFINET Technology graduated as Certified PROFINET Engineer”
TRA-PN-TOOLS On-site training: PROFINET tools

Please contact us

People interested in this product, may be interested in :

 

Echochange

echochange

Ethernet Gateway for the Connection of Different Controllers

The echochange protocol converter supports Ethernet TCP/IP protocols of such leading manufacturers as Siemens, Schneider Electric and Rockwell Automation. This simple protocol conversion makes communication between automation systems of different manufacturers quick and easy.

 

Protocol Conversion for Data Exchange between Multi-Vendor Automation Systems

  • Integration of robust control technology without having to adjust control software
  • Combination of separate networks with different media via configured connections
  • Connection of physically separate networks with different media or heterogeneous networks with identical medium
  • Connection of data from different control systems via allocation tables
  • Bi-directional conversion and writing of PLC data via configured connections
  • Analysis of device functionality and extensive Ethernet diagnostics

Support of Multiple Industrial Standard Protocols

  • Support of TCP, UDP, IP, ISO (H1), ISO on TCP (RFC1006), PLC Header, EtherNet/IP Ethernet protocols
  • Linking of computers with TCP/IP to ISO (H1) networks
  • Remote maintenance of ISO (H1) networked controllers via TCP/IP
  • Routing support for controllers

Investment Protection and IT Maintenance Cost Reduction

  • Standard component for extending functionality without modifying existing systems
  • Very easy configuration through straight-forward project import without requiring control modifications and programming skills
  • Remote configuration and diagnosis via remote maintenance if required
  • No need for additional PC with software updates and additional administration
  • Working for years once configured – untouched, without updates, and with zero maintenance costs
  • Supporting plug-and-go replacement if required based on configuration data stored on SD card
Ethernet Addressable Controllers Siemens S7 and S5, Rockwell Automation ControlLogix, CompactLogix, PLC-5 and SLC-500, Modbus TCP controllers (e.g. Schneider Electric, Phoenix, Contact Wago, Beckhoff), Mitsubishi (Melsec-Q), etc.
Ethernet Protocols TCP/IP, RFC1006 (ISO on TCP), ISO (H1), EtherNet/IP, AB Ethernet, S5, S7, CLX, SLC, Send/Receive (raw data / socket), TCP/IP with PLC header, Modbus TCP, Melsec-Q, DLMS, DCU
Protocol Conversion
  • RFC1006: to ISO(H1), CLX/SLC, AB Ethernet, Melsec-Q, Modbus TCP
  • ISO (H1): to RFC1006, ISO(H1), CLX/SLC, AB Ethernet, Melsec-Q, Modbus TCP
  • Modbus TCP: to RFC1006, CLX/SLC, AB Ethernet, Melsec-Q
Ethernet Interfaces 2xTP (RJ45), 10/100MBit/s
Power Supply 24VDC, ca. 0,3A
Ambient Conditions Operating Temperature: 0 to 55 °C,  Storage Temperature: -20 to 70 °C
Dimensions (HxWxL) 131mm x47mm x 111mm
Weight ca. 0,4kg
Mounting 35mm DIN Rail
Protection Class IP20
Certifications CE, FCC, VCCI
GPL-YY-142101 echochange, Maximum 10 Connections;
Connectors: 2xEthernet
LRA-YY-142001 Upgrade echochange: Maximum 30 Connections

Additional Products and Services

700-5596-04 AC Adapter, 24VDC, Euro, UK, or USA
120-1010-05 Telephone support: application consulting, fees charged on a time and materials basis
110-1000-01 Training “Industrial Ethernet: Troubleshooting in Automation Plants“, 3 days

Scope of Delivery

Hardware Protocol converter echochange, SD Card 2 GB, connector for power supply*
Software Configuration software NetCon on CD-ROM
Documentation Quick Start leaflet, integrated help , product manual on CD-ROM

* A plug-in powerpack is not included. If necessary, please order this separately.

For training courses, please ask

Connector Power Pack 24 V DC

Country-specific connector power packs are available. Note: A connector power pack is not included in the delivery of the echochange. If necessary please order it separately.

Technical Details

100 – 240 V AC, 47 – 63 Hz, sec. 24 V, 1,25A

pnGate PA

PROFINET to PROFIBUS PA Gateway (pnGate PA)

Direct PROFIBUS PA Segment Integration into PROFINET Control Systems

  • Re-use of Existing Power Conditioners in Technology Upgrade Projects
  • No PROFIBUS DP Intermediate Segment required
  • Prepared for Integration in Standard Engineering and Plant Asset Management Tools

Key Component for Transition to State-of-the-Art Technology

  • Simple replacement of installed PROFIBUS DP/PA segment couplers
  • Re-use of existing PROFIBUS PA segments without requiring modification
  • Support of PROFINET redundancy for increased reliability

Direct Connectivity to PROFIBUS Segments

  • Acting as PROFINET Device and PROFIBUS PA Master
  • Support of up to 4 PROFIBUS PA segments

Configuration, Parameterization and Plant Asset Management Using Standard Industry Tools

  • Supports major PROFINET engineering tools such as TIA Portal, Step7 and PC WORXS
  • Included CommDTM allowing use in FDT/DTM frame applications
  • EDD-based device parametrization using Siemens Simatic PDM
Technical Details
Hardware Processor
Status LEDs (Gateway)Status LEDs (Fieldbus)
Altera Cyclone V SoC with dual-core ARM Cortex-A9
PWR (power supply), RUN (operation), ERR (error), CFG (configuration and update)
SF (system fault), BF (bus fault)
Interfaces and Connectors Ethernet

PROFIBUS PA

2 * IEEE 802.3 100BASE-TX / 10BASE-T, embedded PROFINET switch for daisy chain topology
Connectors: RJ45
Protocol: PROFINET RT / IRT, Support of PROFINET redundancy protocols
RESTful API interface for device configuration
Up to 4 PROFIBUS PA (MBP) segments (refer to the section “Order Numbers”),
Bus-powered Medium Attachment Unit (MAU): Fieldbus voltage range: 9 VDC … 32 VDC,
current consumption 10 mA,
Connectors: 3-position screw connection, galvanically isolated
Physical Properties Dimensions (H x W x D)
Weight
Power SupplyOperating / Storage Temperature
Relative Humidity
Cooling
Coating
Mounting
Protection Class
100 mm x 35 mm x 105 mm
About 0.25 kg
18 VDC … 32 VDC; SELV/PELV power supply mandatory
Typical input current: 200 mA, maximum input current: 1 A (allowing for in-rush current at switch-on)
No power supply to PROFIBUS PA segments through pnGate PA
-40 °C … +70 °C / -40 °C … +85 °C
(see detailed mounting description in user manual)
10 % … 95 %, non-condensing
Convection, no fan
Conformal coating based on ANSI / ISA-S71.04 G3
DIN rail 35 mm
IP20
Scope of Delivery
Hardware pnGate PA Gateway
Software GSDtoGSDML Converter, FDT CommDTM, PACTware, Drivers and Tools
Documentation On CD-ROM
Order Numbers
GCA-AL-024602 pnGate PA, PROFINET to PROFIBUS-PA Gateway. Supports up to 2 PROFIBUS PAsegments (up to 32 PA devices).
GCA-AL-024604 pnGate PA, PROFINET to PROFIBUS-PA Gateway. Supports up to 4 PROFIBUS PAsegments (up to 64 PA devices).
GCA-AL-024605 pnGate PA (for STAHL carrier), PROFINET to PROFIBUS-PA Gateway. Supports up to 4 PROFIBUS PA segments (up to 64 PA devices). For reversed mounting position on STAHL backplane.
Additional Products and Services
GCA-AN-024608 pnGate PB, PROFINET to PROFIBUS Gateway. Supports up to 2 PROFIBUS PAsegments (up to 32 PA devices, MBP physical layer) and 1 PROFIBUS DP segment (RS485).
GCA-EL-024802 mbGate PA, Modbus/TCP to PROFIBUS-PA Gateway. Supports up to 2 PROFIBUS PA segments (up to 32 PA devices).
GCA-EL-024804 mbGate PA, Modbus/TCP to PROFIBUS-PA Gateway. Supports up to 4 PROFIBUS PA segments (up to 64 PA devices).

pnGATE PB

PROFINET to PROFIBUS DP/PA Gateway (pnGate PB )

With the pnGate : Direct Integration of PROFIBUS DP and PA Segments into PROFINET Control Systems

  • Re-use of Existing Power Conditioners in Technology Upgrade Projects
  • No PROFIBUS DP Intermediate Segment required
  • Prepared for Integration in Standard Engineering and Plant Asset Management Tools
csm_pnGate_PB_application_EN_1000px_rgb_4fdcab893e

Key Component for Transition to State-of-the-Art Technology with the pnGATE PB from Softing

  • Simple replacement of installed PROFIBUS DP/PA segment coupler
  • Re-use of existing PROFIBUS segments without requiring modification
  • Support of PROFINET redundancy for increased reliability

Direct Connectivity to PROFIBUS Segments

  • Single access point to PROFIBUS DP and PROFIBUS PA segments from PROFINET networks
  • Acting as PROFINET Device, PROFIBUS PA and PROFIBUS DP Master
  • Support of one PROFIBUS DP segment and up to two PROFIBUS PA segments

The pnGate PB, allows you configuration, parameterization and plant Asset Management using standard industry tools

  • Supports major PROFINET engineering tools such as TIA Portal, Step7 and PC WORXS
  • Included CommDTM allowing use in FDT/DTM frame applications
  • EDD-based device parametrization using Siemens Simatic PDM
Technical Details
Hardware Processor
Status LEDs (Gateway)Status LEDs (Fieldbus)
Altera Cyclone V SoC with dual-core ARM Cortex-A9
PWR (power supply), RUN (operation), ERR (error), CFG (configuration and update)
SF (system fault), BF (bus fault)
Interfaces and Connectors Ethernet

PROFIBUS PA

PROFIBUS DP-V0 / V1

2 * IEEE 802.3 100BASE-TX / 10BASE-T, embedded PROFINET switch for daisy chain topology
Connectors: RJ45
Protocol: PROFINET RT / IRT, Support of PROFINET redundancy protocols
RESTful API interface for device configuration
2 * PROFIBUS PA (MBP) segments,
Bus-powered Medium Attachment Unit (MAU): Fieldbus voltage range: 9 VDC … 32 VDC,
current consumption 10 mA,
Connectors: 3-position screw connection, galvanically isolated
1 Segment with RS485 Physical Layer, Connector: 9-pin Sub-D socket
Physical Properties Dimensions (H x W x D)
Weight
Power SupplyOperating / Storage Temperature
Relative Humidity
Cooling
Coating
Mounting
Protection Class
100 mm x 35 mm x 115 mm
Approx. 0.25 kg
18 VDC … 32 VDC; SELV/PELV power supply mandatory
Typical input current: 200 mA, maximum input current: 1 A (allowing for in-rush current at switch-on)
No power supply to PROFIBUS PA segments through pnGate PB
-40 °C … +70 °C / -40 °C … +85 °C
(see detailed mounting description in user manual)
10 % … 95 %, non-condensing
Convection, no fan
Conformal coating based on ANSI / ISA-S71.04 G3
DIN rail 35 mm
IP20
Scope of Delivery
Hardware pnGate PB Gateway
Software GSDtoGSDML Converter, FDT CommDTM, PACTware, Drivers and Tools
Documentation On CD-ROM
Order Numbers
GCA-AN-024608 pnGate PB, PROFINET to PROFIBUS Gateway. Supports up to 2 PROFIBUS PA segments (up to 32 PA devices, MBP physical layer) and 1 PROFIBUS DP segment (RS485).
Additional Products and Services
GCA-AL-024602 pnGate PA, PROFINET to PROFIBUS-PA Gateway. Supports up to 2 PROFIBUS PA segments (up to 32 PROFIBUS PA devices).
GCA-AL-024604 pnGate PA, PROFINET to PROFIBUS-PA Gateway. Supports up to 4 PROFIBUS PA segments (up to 64 PROFIBUS PA devices).
GCA-AL-024605 pnGate PA (for STAHL carrier), PROFINET to PROFIBUS-PA Gateway. Supports up to 4 PROFIBUS PA segments (up to 64 PROFIBUS PA devices). For reversed mounting position on STAHL backplane
GCA-EL-024802 mbGate PA, Modbus/TCP to PROFIBUS-PA Gateway. Supports up to 2 PROFIBUS PA segments (up to 32 PROFIBUS PA devices).
GCA-EL-024804 mbGate PA, Modbus/TCP to PROFIBUS-PA Gateway. Supports up to 4 PROFIBUS PA segments (up to 64 PROFIBUS PA devices).

( coming soon )

pnGate PA/PB Configuration in TIA Portal

Easy Parameterization of PROFIBUS PA Devices in SIMATIC PDM with pnGate PA

THScope

Management and Diagnostics for Industrial Networks

TH SCOPE is a software product for industrial network management and network diagnostics. Geared to plant operators and maintenance personnel, TH SCOPE is an all-in-one, easy-to-use solution for permanent monitoring and predictive maintenance, for acceptance testing and for troubleshooting. Combined with TH LINK components, the product supports PROFIBUS, PROFINET, EtherNet/IP and Modbus TCP protocols.

Comprehensive Presentation and Evaluation of Diagnostic Data

  • Provision of data on network communication, network configuration and diagnostic messages
  • Preparation of standardized exports (e.g. for acceptance testing)
  • Support of PROFIBUS, PROFINET, EtherNet/IP and Modbus TCP in combination with TH LINK components
  • Data acquisition also from standard Ethernet devices (e.g. PCs or camera systems)

Versatile solution for a wide range of diagnostic applications

  • Permanent monitoring and alerting
  • Commissioning and acceptance
  • Network documentation
  • Network and Plant Asset Management
  • Fault localization and identification

Flexible System and Process Integration

  • Web-based access, local or remote
  • Integration of inventory data into monitoring tools and process control systems via OPC UA
  • Export of diagnostic data for further processing in other applications (e.g. MS Excel)
  • Easy data exchange with Softing‘s Analyzer IE software (e.g. export of reference measurement)
  • Intuitive handling and operation
Technical Data
Functionality
  • Network overview with network and device status plus diagnostic messages with troubleshooting recommendations
  • Analysis of device logs
  • Live list, statistics, inventory
  • GSDML file support, plaintext messages in diagnostic list
  • Topology and trend analysis
  • Automatic e-mail notification in case of fault
  • Reference comparison
  • Acceptance measurements and acceptance reports
  • Configurable time intervals for automated export of inventory and topology data
  • Data export via Excel
  • Output of inventory data via OPC UA
Supported Protocols PROFINET, PROFIBUS, EtherNet/IP, Modbus TCP
Interfaces
  • SNMP Agent
  • OPC UA-Server
  • OPC Classic DA-Server
System Requirements
  • Web browser with Adobe Flash Player 14 or higher
  • Adobe Reader 8 or higher for reading the documentation and for printing the topology
Supported Operating Systems Windows 7, Windows 8.1, Windows 10
Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Network Access Data collection through TH LINK (PROFIBUS, PROFINET, EtherNet/IP, Modbus TCP und Industrial Ethernet)
Demoversion Full TH SCOPE functionality can be used for free for 30 days after installation
Licensing Via software or hardware key
Scope of Delivery
Software TH SCOPE (by download from Softing‘s website industrial.softing.com)
License Software or hardware key
Documentation Installation Manual, User Manual, Release Note
Order Numbers
LRA-JY-003024 TH SCOPE (software key)
LRL-JY-003025 TH SCOPE (hardware key)
Additional Products and Services
GEA-JN-003006 TH LINK PROFIBUS
GDA-JA-003034 TH LINK PROFINET
GDA-JY-003037 TH LINK Industrial Ethernet
LRA-JY-003028 TH LINK PC Industrial Ethernet

TH SCOPE:
If your network is protected by a second firewall in addition to the Windows firewall, make sure that the following settings are made to allow TH SCOPE services to communicate properly.

  • Enabling of HTTP port 80 – inbound and outbound
  • Enabling of SNMP port 161 inbound or port 2367 (if port 161 is used by another SNMP agent).
  • Enabling of IP 224.0.5.128 port 2364 UDP outbound
  • Enabling of UDP ports 2365 outbound and 2366 inbound

 

The following ports are used by TH SCOPE for internal communication only:

  • Port 22
  • Port 80
  • Port 1100
  • Ports 1123 – 1151
  • Port 1500
  • Port 1501
  • Ports 2363 – 2366
  • Ports 49152 – 49171

I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.

People interested in this product, can be interested in :

THLink Industrial Ethernet

Industrial Ethernet Network Diagnostics Independent from Controller and Control Room

The TH LINK Industrial Ethernet diagnostics tool makes use of a controller-independent access to monitor PROFINET, EtherNet/IP and Modbus TCP networks. The diagnostic data is collected in networks comprising up to 254 nodes, and made available to users through the TH SCOPE software application. TH LINK Industrial Ethernet is easy to use and can be integrated without interfering with the operation of existing installations.

csm_THLink_IE_D_EN_170101_311_fbdb7e6c27

Independent Access to PROFINET, EtherNet/IP and Modbus TCP Networks

  • Controller-independent
  • Independent of configuration tools
  • Only one tool needed to monitor multiple IP subnetworks (up to 254 nodes, one or more controllers

Designed for Installation without Interference with Plant Operation

  • Connection to free port in industrial network, also possible during operation of the plant
  • No need to install TAPs or use mirror ports
  • Highest security (separate accesses for control room level and plant level, no routing)
  • Easy integration into existing plants thanks to compact design

Powerful Data Collection Capabilities Optimized for Ethernet-Based Industrial Communication

  • Support of the PROFINET, EtherNet/IP and Modbus TCP protocols
  • Collection also from standard Ethernet devices (e.g. PCs or camera systems)
  • PROFINET supervisor in PROFINET networks
  • Network load limit according to PROFINET guidelines

Optimized for Use by Maintenance Engineers

  • Suitable for network acceptance testing, continuous monitoring and troubleshooting
  • Easy and intuitive handling and operation
  • Fault identification with intelligent troubleshooting assistance
  • Seamless integration with TH SCOPE diagnostics software
Functionality
  • Network detection and data collection
  • Alarm notification in case of fault
  • Basic monitoring, configuration
  • Integrated web server
Input Voltage 24 VDC (18 VDC … 32 VDC)
Current consumption max. 180 mA
Current consumption relay contact max. 100 mA
Operating Temperature -40 °C … +75 °C
Relative Air Humidity 5 … 95 % (no condensation)
Ethernet Ports RJ-45 (10Base-T/100Base-TX)
Supported SD Cards See Release Notes
Mounting 35 mm DIN rail
Dimensions (HxWxD) 22.5 x 99 x 114.5 mm
Weight 120 g
Certifications CE
GDA-JY-003037 TH LINK Industrial Ethernet

Scope of Delivery

Hardware TH LINK Industrial Ethernet
Documentation Installation Manual, Release Note (by download)

Additional Products and Services

ATV-LRA-JY-003024 TH SCOPE (software key)
ATV-LRL-JY-003025 TH SCOPE (hardware key)
ATV-LRA-JY-003028 TH LINK PC Industrial Ethernet (software key)
ATV-LRL-JY-003029 TH LINK PC Industrial Ethernet (hardware key)
ATV-TRA-PN-TECH Training “PROFINET Technology”
ATV-TRA-PN-CERTENG Training “PROFINET Commissioning and Troubleshooting”

FG-260

FG-260 : Ethernet IP -> PROFINET Gateway

FG-260

FG-260 : EtherNet/IP to PROFINET Gateway with PROFINET Controller Functionality

The FG-260 implements a gateway between EtherNet/IP and PROFINET networks. It supports EtherNet/IP Adapter and PROFINET Controller functionality. The integration in PLC programs is provided via EtherNet/IP means, while the PROFINET communication is defined using a configuration tool (e.g. Communication Configuration Tool as included in scope of delivery). The runtime operation can be monitored and adjusted using a built-in web server.

FG-260 Gateway

Simple Integration Through Add-On Instructions

  • Data access of PLC program to PROFINET Devices without requiring detailed PROFINET knowledge
  • Mapping between the two protocols generated by provided tools
  • Usage of Add-On Instructions (AOI), containing detailed PROFINET data type definitions
  • Transparent communication overcoming protocol differences

Time Saving Configuration Creation and Verification

  • Configuration tool for online access to PROFINET Devices via the network
  • Easy assignment of device properties
  • Early identification of discrepancies between offline configuration and real situation

Built-In Web Server For Monitoring And Interaction

  • Status information about both protocols
  • Monitoring of mapping as well as of exchanged data
  • Individual modification of FG-260 settings, including address information
  • Download and upload of all FG-260 configuration information using web server

Different Use Cases are addressed

  • Direct access from Ethernet/IP Scanner in the PLC to PROFINET field devices
  • Access to machines with internal PROFINET network by deploying I-Device capabilities
Hardware
Processor Altera Cyclone V SoC with Dual-core ARM Cortex-A9
Status LEDs (Gateway) PWR (power supply), RUN (running), ERR (error), CFG (configuration upload)
Status LEDs (EtherNet/IP) Net (network), Mod (module)
Status LEDs (PROFINET) SF (system fault), BF (bus fault)
Connectors 2 x IEEE 802.3 100BASE-TX/10BASE-T (1 Ethernet port per protocol)
Dimensions (HxWxD) 100 mm x 35 mm x 105 mm
Weight ca 0.25 kg
Power Supply 18 VDC … 32 VDC, SELV/PELV supply mandatory
Typically 200 mA, maximum 1 A at switch-on
Operating Temperature, Horizontal DIN Rail Installation -40 °C … 55 °C (0 mm minimum distance)
-40 °C … 65 °C (17.5 mm minimum distance)
Operating Temperature, Vertical DIN Rail Installation -40 °C … 40 °C (0 mm minimum distance)
-40 °C … 50 °C (17.5 mm minimum distance)
Storage Temperature -40 °C … 85 °C
Relative Humidity 10 % … 90 %, non condensing
Cooling Convection, no fan
Mounting DIN Rail (35 mm)
Protection Class IP20
Software
Protocols EtherNet/IP Adapter (Up to 2 input and 2 output assemblies with up to 255 Bytes data each, minimum RPI: 8 ms)
PROFINET Controller (up to 8 devices at 1 ms cycle time)
Additional Functionality Mapping application, web server
Supported Versions of Rockwell Automation PLC Programming Software V16 – V21
Emission Conformity EC Directive 2004/108/EG “Electromagnetic Compatibility“, EN 55011, Group 1, Class A
EC Directive 2004/108/EG “Electromagnetic Compatibility“, EN 55022, Class A
EC Directive 2004/108/EG “Electromagnetic Compatibility“, EN 61000, Part 6-4
FCC CFR45, Part 15 Section 15.107 and 15.109 (Class A),
VCCI Class A Information Technology Equipment 2002
Immunity Conformity EC Directive 2004/108/EG “Electromagnetic Compatibility“, EN 61000, Part 6-2
Certifications CE
EN/IEC 61010-1 and CB
EN/IEC 61010-2-201 and CB
UL 61010-1 and UL 61010-2-201
GCL-CA-010260 FG-260

Scope of Delivery

Hardware Gateway FG-260
Software EDS File, Common Configuration Tool on CD-ROM, Search-and-Configure Tool
Documentation Quick Startup Guide as printed documentation, User Guide on CD-ROM

Training on demand

People interested in this product, might be interested in :

THLink Profinet

THLink – PROFINET

THLink Profinet

PROFINET Diagnostics Independent from Controller and Control Room

The TH LINK PROFINET diagnostics tool makes use of a controller-independent access to monitor PROFINET networks. The diagnostic data is collected in networks comprising up to 254 nodes, and made available to users through the TH SCOPE software application. TH LINK PROFINET is easy to use and can be integrated without interfering with the operation of existing installations.

Independent Access to PROFINET Network

  • Controller-independent
  • Independent of configuration tools
  • Only one tool needed to monitor multiple IP subnetworks (up to 254 nodes, one or more controllers)

Designed for Installation without Interference with Plant Operation

  • Connection to free port in PROFINET network, also possible during operation of the plant
  • No need to install TAPs or use mirror ports
  • Highest security (separate accesses for control room level and plant level, no routing)
  • Easy integration into existing plants thanks to compact design

Powerful Data Collection Capabilities Optimized for PROFINET

  • Collection from PROFINET devices and other nodes (e.g. PCs or camera systems)
  • PROFINET supervisor in PROFINET networks
  • Network load limit according to PROFINET guidelines

Optimized for Use by Maintenance Engineers

  • Suitable for network acceptance testing, continuous monitoring and troubleshooting
  • Easy and intuitive handling and operation
  • Fault identification with intelligent troubleshooting assistance
  • Seamless integration with TH SCOPE diagnostics software
Functionality
  • Network detection and data collection (active/passive for PROFINET Networks)
  • Alarm notification in case of fault
  • Basic monitoring, configuration
  • Integrated web server
Input Voltage 24 VDC (18 VDC … 32 VDC)
Current consumption max. 180 mA
Current consumption relay contact max. 100 mA
Operating Temperature -40 °C … +75 °C
Relative Air Humidity 5 … 95 % (no condensation)
Ethernet Ports RJ-45 (10Base-T/100Base-TX)
Supported SD Cards See Release Notes
Mounting 35 mm DIN rail
Dimensions (HxWxD) 22.5 x 99 x 114.5 mm
Weight 120 g
Certifications CE
GDA-JA-003034 TH LINK PROFINET

Scope of Delivery

Hardware TH LINK PROFINET
Documentation Installation Manual, Release Note (by download)

Additional Products and Services

LRA-JY-003024 TH SCOPE (software key)
LRL-JY-003025 TH SCOPE (hardware key)
LRA-JY-003028 TH LINK PC Industrial Ethernet (software key)
LRL-JY-003029 TH LINK PC Industrial Ethernet (hardware key)
GDA-JY-003037 TH LINK Industrial Ethernet
TRA-PN-TECH Training “PROFINET Technology”
TRA-PN-CERTENG Training “PROFINET Commissioning and Troubleshooting”