mbGate PB

mbGatePB

MODBUS TCP SERVER to PROFIBUS PA/DP Master Gateway

imple connection of PROFIBUS Slave Devices to Modbus Control Systems via Internal I/O Mapping

With mbGate PB it is possible to integrate up to 2 PROFIBUS PA segments and 1 PROFIBUS DP segment into Modbus TCP control systems. It acts as Modbus TCP Server and PROFIBUS Master. With our gateway the engineering costs can be reduced since it re-uses existing power conditioners in technology upgrade projects. It enables configuration, parameterization and plant asset management using standard industry tools.

Similar solutions:
mbGate PA: Modbus TCP to PROFIBUS PA Gateway – Integrate PROFIBUS PA segments into Modbus Control system
mbGate DP: Modbus TCP to PROFIBUS DP Gateway – Integrate PROFIBUS DP segments into Modbus Control system

Key Component for Transition to State-of-the-Art Technology

  • Simple replacement of installed PROFIBUS DP/PA segment couplers
  • Re-use of existing PROFIBUS segments without requiring modification

Direct Connectivity to PROFIBUS Segments

  • Single access point to PROFIBUS DP and PROFIBUS PA segments from Modbus TCP networks
  • Acting as Modbus TCP Server and PROFIBUS PA and PROFIBUS DP Master
  • Support of one PROFIBUS DP segment and up to two PROFIBUS PA segments

Configuration, Parameterization and Plant Asset Management Using Standard Industry Tools

  • Supports major Modbus engineering tools such as Schneider Unity Pro or Siemens TIA Portal
  • Included CommDTM allowing use in FDT/DTM frame applications
  • EDD-based device parametrization using Siemens Simatic PDM

MODBUS/TCP Redundancy

  • Supports the use of two redundant PLCs and two redundant gateways
  • Easily enabled via licensing
  • Full control of redundant operation mode via engineering and PLC
Scope of Delivery
Hardware mbGate PB Gateway
Documentation On Website
Order Numbers
GCA-EN-024808 mbGate PB, Modbus TCP to PROFIBUS Gateway. Supports 2 PA segments (up to 32 PA devices, MBP physical layer) and 1 PROFIBUS DP segment (RS485).
Additional Products and Services
LRA-EN-024851 gatePlus HighAvailability, License for activating redundancy features in mbGate PB
LRL-DY-134501 dataFEED OPC Suite, Version 4.01 and higher, including all supported PLC protocols, support for OPC UA, access for any number of dataFEED OPC Tunnel Clients, for simultaneous access to a total of up to 100 OPC UA Servers, OPC Servers and OPC Tunnel Servers, and many more Functionalities such as Database and File Access, Data Exchange, Optimizer, Concentrator and Bridge
GCA-EL-024802 mbGate PA, Modbus TCP to PROFIBUS PA Gateway. Supports up to 2 PA segments (up to 32 PA devices).
GCA-EL-024804 mbGate PA, Modbus TCP to PROFIBUS PA Gateway. Supports up to 4 PA segments (up to 64 PA devices).
GCA-EN-024806 mbGate DP, Modbus TCP to PROFIBUS DP Gateway. Supports 1 PROFIBUS DP segment (RS485).
Fieldbus Infrastructure
Installation solutions When using the high-power trunk topology or FISCO, we offer in cooperation with R.Stahl, fieldbus infrastructure components with PROFIBUS PA and FOUNDATION fieldbus H1 – this ranges from power supply, physical layer diagnostics and field device couplers to termination resistors.

NetXpertXG

ATEVA Technologie : NetXpert

Test your Ethernet cable. Prove the speed limit.

ATEVA Technologie : NetXpert

Wireless access point speeds at the end of the network are out-pacing the speeds of the installed cabling in the middle of the network. Is it possible that your installed cabling will handle speeds beyond design spec and will keep up with speeds of the new wireless access points? Is it possible to leave your CAT 5e and CAT 6 cables in place, and achieve 1Gbit/sec speeds?  10Gbits/sec speeds?

To find out, with the single press of a button, three key tests are run with the NetXpert XG. In one click, NetXpert XG performs a live speed test sending 1Gb/s through your cable (BERT), and will prove if the cable will perform beyond design spec and keep pace with the speed of newly installed access points.

NetXpert XG is the only cable tester and active network manager to perform BERT (bit error rate test), SNR (signal-to-noise ratio), and delay skew to 1G, 5G, or 10G speeds at the press of a button. Now you can perform real-time bit throughput tests to see if your installed cables will run up to 10Gb.

 

One touch bit error rate test, signal-to-noise ratio, and delay skew

By performing a Bit Error Rate Test (BERT) and standards based tests as per IEEE 802.3an, the NetXpert XG proves the error-free data transmission up to 10Gb/s.

A one touch auto test includes BERT, signal-to-noise ratio (SNR), and delay skew, all of which can impact Gigabit transmission.

Signal-to-noise ratio checks to ensure noise is low enough and signal is high enough for reliable transmission.  Delay skew indicates the signal time delay between the wire pairs. Excessive delay from one pair can result in a serious degradation of transmission performance making it impossible for the receiver to interpret the data stream correctly.

All three crucial measurements for determining reliable data transmission are performed at the touch of a button.  When you are ready to test the next cable, hit test again, and NetXpert XG advances automatically to the next cable being tested.  Each test result is automatically stored to a summary report and a detailed report in pdf, csv, or xml format.

The cable qualifier that is defining a new category — the cable project qualifier

If you are a cable installer, network owner, network builder, or system integrator, you’ll be excited to hear that NetXpert XG includes a project editor and auto test generator for up to 1000 cables, and test reports you can keep for your records or leave with your customer.  Once the tests are created, plug in the cable, click test, and NetXpert XG starts testing the cable to IEEE 802.3 standards to prove the speed of your cable.  Not only do you get a wiremap and cable length, NetXpert XG tests BERT, SNR, Delay Skew, distance to opens, shorts, or miswires.  As a bonus you get active network tests for copper, fiber, and wireless.  And, with 2 NetXpert XG local units, you can test fiber cables.

Cable Project Qualifier

  • Use the project editor, cable test editor, test label editor to pre-configure your cable testing projects
  • Press test to automatically sequence up to 1000 cable tests from the local or remote device to increase cable testing efficiency when working alone
  • Test data cabling for IEEE 802.3 compliance at data rates up to 10 Gb/s (BERT)
  • Determine signal-to-noise ratio (SNR) for compliance up to 10 Gb/s
  • Measure delay skew for compliance up to 10Gb/s
  • Measure length of cable with TDR and capacitance measurements for highly accurate test results and easier troubleshooting
  • Full-color wire map shows distance to open, distance to short, miswires, split pairs, and shield on a color graphical display
  • Save test results and generate standards-based measurement reports providing “Pass/Fail” indication in pdf, csv, or xml format

Perform active network management

  • Support for IPv4 and IPv6
  • Discover your network and see the connected network devices
  • Identifies defective PoE switches with a PoE load test
  • DHCP test
  • Ping lists can be defined and saved for later use
  • LLDP/CDP detection and analysis
  • Identifies VLANs present in your network
  • Data transfer from the tester to the PC using USB stick, wireless, or bluetooth connectivity
Length Measurement Technology Time-Domain Reflectometry (TDR) and capacitance
Cable Measurements Cable Testing and ID: up to 1,000 ft (305 m)
Split Pair Detection: 3 ft (1 m) to 1,000 ft (305 m)
Length Measurement: 0 to 1,500 ft (457 m), ± (5%+1ft (30 cm))
Distance to fault: 0 to 656 ft (200 m) ± (5% + 3ft (1m))
Supports 8 wiremap remotes (RJ 45) and 24 RJ-45 ID only
remotes
Power over Ethernet (PoE) Test supports IEEE 802.3af PoE (Type 1, max 15.4W),
IEEE 802.3at PoE+ (Type 2, 30W) and 802.3bt PoE++ (Type 3, 60W)
Future proofed for IEEE 802.3bt Type 4 100W higherpower PoE
Active Ethernet Network and test support by interface:
Copper RJ-45 interface –100/1,000/2,500/5,000/10,000 Mb/sec link speeds
Fiber SFP+ #1 interface supports 10Gb/sec link speed
Fiber SFP+ #2 interface supports 1Gb/sec link speed
WiFi 802.11 a/b/g/n 2.4 Ghz WiFi and Bluetooth
Maximum Voltages Maximum voltage that can be applied to any 2 connector pins without causing damage to the tester:
RJ-45: 60 VDC or 50 VAC
Save Test Results Stores virtually unlimited cable or network tests with user defined names per project
Tone Generation Tone Frequencies: 730 Hz and 1440 Hz
Languages English, German, French, Spanish
Battery Li-Ion, 7.2 VDC, 3.1A-hr (typical)
Battery Life at 10Gb: 5 hrs minimum, 24 hrs stand-by
Temperature Operating: 14 to 140° F (-10 to 60°C)
Storage: -22 to 158°F (-30 to 70°)
Humidity 10 to 90% non-condensing
Enclosure Injection molded plastic
Display 7″ Color TFT-LCD capacitive touch display,
1024 x 600 resolution (WSVGA)
Size 245 x 177 x 73 mm (main unit)
130 x 177 x 55 mm (Active Remote)
Weight with Battery 2.6lbs (1.2 kg) main unit
1.3lbs (0.6 kg) Active Remote

mbGate PA

MODBUS TCP SERVER to PROFIBUS PA Master Gateway

Simple connection of PROFIBUS PA Slave devices to Modbus control systems via internal I/O mapping

With mbGate PA it is possible to integrate up to 4 PROFIBUS PA segments into Modbus TCP control systems. It acts as Modbus TCP Server and PROFIBUS PA Master. With our gateways the engineering costs can be reduced since it re-uses existing power conditioners in technology upgrade projects. It enables configuration, parameterization and plant asset management using standard industry tools.

Similar solutions:
mbGate PB: Modbus TCP to PROFIBUS PA/DP Gateway –  Integrate PROFIBUS DP/PA segments into Modbus Control Systems
mbGate DP: Modbus TCP to PROFIBUS DP Gateway – Integrate PROFIBUS DP segments into Modbus Control system

 

Key Component for Transition to State-of-the-Art Technology

  • Simple replacement of installed PROFIBUS DP/PA segment couplers
  • Re-use of existing PROFIBUS PA segments without requiring modification

Direct Connectivity to PROFIBUS Segments

  • Acting as Modbus Server and PROFIBUS PA Master
  • Connects up to 4 PROFIBUS PA Segments to Modbus TCP

Configuration, Parameterization and Plant Asset Management Using Standard Industry Tools

  • Supports major Modbus engineering tools such as Schneider Unity Pro or Siemens TIA Portal
  • Included CommDTM allowing use in FDT/DTM frame applications
  • EDD-based device parametrization using Siemens Simatic PDM

Scope of Delivery
Hardware mbGate PA Gateway
Documentation On Website
Order Numbers
GCA-EL-024802 mbGate PA, Modbus TCP to PROFIBUS PA Gateway. Supports up to 2 PA segments (up to 32 PA devices).
GCA-EL-024804 mbGate PA, Modbus TCP to PROFIBUS PA Gateway. Supports up to 4 PA segments (up to 64 PA devices).
Additional Products and Services
LRL-DY-134501 dataFEED OPC Suite, Version 4.01 and higher, including all supported PLC protocols, support for OPC UA, access for any number of dataFEED OPC Tunnel Clients, for simultaneous access to a total of up to 100 OPC UA Servers, OPC Servers and OPC Tunnel Servers, and many more Functionalities such as Database and File Access, Data Exchange, Optimizer, Concentrator and Bridge
GCA-EN-024806 mbGate DP, Modbus TCP to PROFIBUS DP-Gateway. Support of 1 PROFIBUS DP segment (RS485).
GCA-EN-024808 mbGate PB, Modbus TCP to PROFIBUS Gateway. Supports 2 PA segments (up to 32 PA devices, MBP physical layer) and 1 PROFIBUS DP segment (RS485).

uaGATE 840D

OPC UA Server Gateway for Siemens SINUMERIK 840D Controllers

The gateway allows reading the complete SINUMERIK 840D machine tool data. It provides access to the NC part with its axis, tool, program and drive data as well as specific alarms. In addition, a connection to the integrated SIMATIC Siemens S7 can be established. The data from both connections are available via the OPC UA and MQTT interfaces and thus can be used for various Industrie 4.0 applications.

With uaGate 840D, important spindle and axis data, such as torque and power consumption, can be read and reused in various applications. In addition, the active program as well as sub programs and the currently used tool is accessible. For instance, these data are available for condition monitoring, predictive maintenance, for data logging or for analysis tasks, such as spindle and axis monitoring. The gateway can also be used to acquire data from older SINUMERIK 840D controllers. Due to the preconfigured data symbol file for the standard use case based on one channel, three axes and one spindle, the user does not require any specific SINUMERIK know-how for reading the data.

The product can simply get mounted next to the SINUMERIK NCU on a DIN rail and requires 24 VDC power supply. It has two independent Ethernet interfaces, one addressing the machine and the other addressing the IT network. Between these, the gateway acts as a firewall. The configuration is performed in just a few clicks using any web browser and the integrated web server.

csm_840D_EN_9d3a7c6671

Access to Siemens SINUMERIK PLC and NC Kernel Data

  • Access to many different Siemens SINUMERIK 840D Solution Line controllers
  • Data integration into higher level management tools like ERP, MES or SCADA systems
  • Embedded OPC UA Server providing open, platform-independent communication
  • Access to NC area containing axis, tool, program,drive data and specific alarms
  • Use of data for analysis, condition monitoring, predictive maintenance or data logging purposes
  • Additional Siemens licenses not necessary
  • No PLC or NC Unit programming required for configuration

Easy Configuration

  • Usage of predefined symbol files for standard configurations like one channel with one spindle and three axis (four drives)
  • AWL file upload of user-defined NCVar Selector symbol files for NC Kernel connection
  • Easy symbol import from SIMATIC STEP 7 projects for PLC connection
  • Gateway configuration using any standard web browser and integrated web server

Industry-proven Security

  • Physically separated Ethernet interfaces protecting SINUMERIK from unauthorized access via IT network
  • Support of security standards like SSL/TLS, X.509 certificates and user authentication for OPC UA and MQTT communication
Hardware Processor Altera Cyclone V SoC with Dual-core ARM Cortex-A9
Connectors 2 x IEEE 802.3 100BASE-TX/10BASE-T (independent interfaces)
Status LEDs PWR (power supply), RUN (running), ERR (error), SYS (configuration)
Dimensions (H x W x D) 100 mm x 22.5 mm x 105 mm
Power Supply 18 VDC … 32 VDC, SELV/PELV supply mandatory Typically 200 mA, maximum 1 A at switch-on
Operating Temperature, Horizontal DIN Rail Installation -40 °C .. 50 °C (0 mm minimum distance)
-40 °C .. 55 °C (22.5 mm minimum distance)
Operating Temperature, Vertical DIN Rail Installation -40 °C .. 35 °C (0 mm minimum distance)
-40 °C .. 40 °C (22.5 mm minimum distance)
Storage Temperature -40 °C .. 85 °C
Relative Humidity 10 % … 90 %, non-condensing
Weight About 0.2 kg
Mounting DIN Rail (35 mm)
Housing Phoenix Contact ME MAX
Protection Class IP20
Software Protocols SIMATIC S7, SINUMERIK, OPC UA (Server, 20,000 items in total), MQTT (Publisher, up to 1,000 topics)
Supported Controllers Siemens SINUMERIK 840D Solution Line, software version 4.3 and higher
Supported Engineering Tools Siemens NCVar Selector
Conformity Emission EC Directive 2004/108/EC “Electromagnetic Compatibility”, EN 55011, Group 1, Class A
EC Directive 2004/108/EC “Electromagnetic Compatibility”, EN 55022, Class A
EC Directive 2004/108/EC “Electromagnetic Compatibility”, EN 61000, Part 6-4
FCC CFR45, Part 15 Section 15.107 and 15.109 (Class A),
VCCI Class A Information Technology Equipment 2002
Immunity EC Directive 2004/108/EC “Electromagnetic Compatibility”, EN 61000, Part 6-2
Certifications CE, FCC, RoHS
GAA-YX-145144 uaGate 840D
6FC5851-1XC45-4YA8 SINUMERIK 840D sl CNC software and SINUMERIK Operate, toolbox including NCVar Selector
(please order directly from Siemens)

Scope of Delivery

Hardware uaGate 840D
Software Tool for configuration over integrated web interface
Documentation Quick Startup Guide (printed documentation)
Performance :
  • The uaGate 840D gateway can collect up to 20000variables
  • Polling frequency depends on different paramters. Il can be between 15ms to 80ms

SOFTING – DP Configurator

PROFIBUS DP Configurator

PROFIBUS DP configurator : V 2.02

PROFIBUS Configurator is a versatile configuration tool. It allows the user to define PROFIBUS
networks from a master’s point of view. PROFIBUS Configurator can be used in various application
scenarios to configure Softing PROFIBUS DP masters.
Depending on the use case the functionality reaches from defining the network structure with its
connected devices and their individual device parameters over interactive online tests of particular
inputs and outputs up to the definition of tag names and data types for all available process data as
they are used by Softing’s PROFIBUS OPC server.

Offline configuration
The goal of an offline configuration is to prepare a binary configuration file for a controller that
uses a Softing PROFIBUS DP master. The PROFIBUS DP master may either be based on a PC interface board or implemented as an
embedded solution using Softing’s protocol stacks and IP cores.

Online configuration
Online configuration makes use of a PROFIBUS interface boards installed on the PC
where the PROFIBUS Configurator is used.

This allows for scanning the network for connected devices and for interactive
communication with these devices. A network configuration can be activated using the interface board as the active master for the devices connected to it. Defining tag names for process variables

For each configured device it is possible to assign named process variables to its inputs and output. These variable are also assigned a data type (e.g. Boolean for
single bits or Signed Byte for an analog input). These variables may subsequently be used inside the PROFIBUS Configurator for purposes like commisioning the network. For that purpose variables can be read and written as soon as the current configuration is activated.
Furthermore, the named variables serve as so-called “OPC items” if such a configuration is used by a Softing PROFIBUS OPC server.

Documents

Software

Release available with a  SOFTING card, as hardware dongle

Référence : VCL-NN-017210

Scope of delivery : Sofware and USB key

dataFEED Exporter

dataFEED Exporter : Export of Siemens Symbols from TIA Portal or STEP 7

exporter_en

Simple Symbol Export

  • Export of symbolic names from Siemens TIA Portal and SIMATIC STEP 7 projects
  • No TIA Portal or STEP 7 know-how required for exporting symbol information
  • Selection of data blocks to be available via Softing products
  • Later adjustment of .sdfi file by adding/deleting individual symbols
  • Chance for changing symbol names afterwards
  • Smart wizard for export in a few steps
  • Display of symbol and syntax information via tooltips

Secure Encrypted Softing Symbol File

  • Creation of encrypted symbol files for import into Softing products
  • Output of exported symbols into encrypted secure .sdfi file
  • Full protection of Siemens project as only symbol information is stored
  • Chance to assign of read / write attributes for exported symbols at later stage

Perfect Addition to Softing Products

  • Software usable with dataFEED OPC Suite, dataFEED OPC Server Siemens, uaGate SI, edgeGate and echocollect e/r/m
  • Installation of dataFEED Exporter on the TIA computer required for export (Openness interface)
  • Free of charge when using Softing products
  • Supporting all current Windows operating systems as well as virtual environments

DataFEED Exporter

  • Simple item syntax export out of Siemens STEP 7 and TIA Portal projects
  • Generation of encrypted symbol file, for import into Softing products
  • For use with dataFEED OPC Suite, uaGate SI, edgeGate and echocollect e/r/m
Supported Controllers Siemens S7-300/400/1200/1500
Supported Engineering Tools SIMATIC STEP 7, TIA-Portal V13/V14/V15 including Service Packs
Supported Operation Systems Windows 7, Windows 8, Windows 8.1, Windows 10
Windows Server 2003, Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Supported Data Types Bool, Byte, Char, Word, Int, DWord, Dint, Real, Date, Time_Of_Day, Time, S5Time, Date_And_Time, String, UInt, USInt, UDInt, Sint, Struct, 0xFFFF (Folder)
Licensing Free when using Softing products
Suitable for echocollect e/r/m, uaGate SI, edgeGate, Industrial IoT Starter Kit, dataFEED OPC Suite, dataFEED OPC Server Siemens
File size 85 MB
Output Encrypted secure Softing .sdfi data file

Archives for previous release available on our mirror site

dataFEED OPC UA .NET Server & Client SDK for Windows

dataFEED OPC UA .NET Server & Client SDK for Windows

  • OPC UA Communication Integration in Windows-based Automation Environments
  • Comprehensive Functionality Provided by Libraries
  • Optimal Total Costs of Ownership Through All-In-One License Model

Complete Solution Addressing All Customer Requirements

  • Comprehensive set of building blocks offering encapsulation and easy-to-use functionality required for implementing OPC UA Clients and Servers for Windows environment
  • Modular design to scale OPC UA functionality according to actual requirements
  • Wide range of available functionality, including Extended Security, Data Access, Complex Data, Events, Alarms & Conditions and Historical Access
  • Integrated security concepts allowing safe remote data transfer actively addressing modern security threats
  • Applicable for time-critical control tasks as well as for complex automation projects
  • OPC UA Servers and Clients capable to move data and information between factory floor and enterprise level

Comprehensive Scope of Delivery for Easy and Fast Development

  • Optimized Application Programming Interface (API) and easy to understand documentation
  • Complimentary how-to example applications, step by step tutorials, complex test and simulation clients and servers for a lean getting started with OPC UA development

Investment Security Through Innovative License Model

  • Implementation according latest OPC UA specifications
  • Free migration to upcoming OPC UA Development Toolkit versions thanks to toolkit software and 3 years‘ right to updates to future versions
OPC Specifications OPC Unified Architecture V1.03
OPC Roles OPC UA Client, OPC UA Server
OPC UA Client/ Server Profiles Core Characteristics, Data Access, Complex Data, Base Eventing, Methods, Audit, Node Management, Historical Access, Alarms and Conditions, Redundancy
OPC UA Transport OPC UA TCP transport; UA Binary Encoding SOAP/HTTP transport: UA Binary and XML encoding HTTPS transport; UA Binary and XML encoding
OPC UA Security Security policy: Basic256Sha256/Basic256/Basic128Rsa15/None
Authentication: anonymous/user name and password/user certificate
Full compliance to OPC UA 1.03 specification
OPC UA Modelling Model designer as helper tool for address space configuration for OPC UA Servers
Programming Interface C#
Development Environment* Microsoft Visual Studio 2010, Microsoft Visual Studio 2012, Microsoft Visual Studio 2013, Microsoft Visual Studio 2015, Microsoft Visual Studio 2017, .NET Framework 4.0, .NET Framework 4.5, .NET Framework 4.6, .NET Framework 4.7
Development /Target
Operating Systems*
Windows 7 (32 Bit and 64 Bit), Windows 8.1 (32 Bit and 64 Bit), Windows 10 (32 Bit and 64 Bit), Windows Server 2008 RS2, Windows Server 2012, Windows Server 2016
Compliance/Certification Regularly tested at OPC Foundation interoperability workshops, test with OPC Foundation compliance test tool
Support Tools Comprehensive programming examples and tutorials, complex test and simulation OPC UA Server and Client applications, generic technology test and demonstration Client and Server tools
Trial Version Trial toolkit assemblies contain complete functionality. Limitation to 90-minute runtime period applies.
Trial version upgrades to unlimited functionality simply by using binary license activation key
Licensing Trial and evaluation license, single seat developer license (binary and source code version)
Applications integrating licensed toolkit libraries can be deployed in unlimited number of copies.

* Please contact the Softing sales representative for requests of different compilers or operating system variants.

Documentations:

  • OPC UA .NET Server & Client SDK Release Note V 1.45.00
  • OPC Competence Brochure

Drivers & Downloads:

LMA-DD-031101 Maintenance and support contract for OPC UA .NET Client Development Toolkit, 3 years minimum period, based on yearly fee, including single seat developer license WRL-DD-031101, binary format
WRL-DD-031101 OPC UA .NET Client Toolkit, single seat developer license, binary format, available only in combination with LMA-DD-031101
LMA-DD-031102 Maintenance and support contract for OPC UA .NET Server Development Toolkit, 3 years minimum period, based on yearly fee, including single seat developer license WRL-DD-031102, binary format
WRL-DD-031102 OPC UA .NET Server Toolkit, single seat developer license, binary format, available only in combination with LMA-DD-031102
LMA-DD-031201 Maintenance and support contract for OPC UA .NET Client Development Toolkit, 3 years minimum period, based on yearly fee, including single seat developer license WQL-DD-031201, source code format
WQL-DD-031201 OPC UA .NET Client Toolkit, single seat developer license, source format, available only in combination with LMA-DD-031201
LMA-DD-031202 Maintenance and support contract for OPC UA .NET Server Development Toolkit, 3 years minimum period, based on yearly fee, including single seat developer license WQL-DD-031202, source code format
WQL-DD-031202 OPC UA .NET Server Toolkit, single seat developer license, source format, available only in combination with LMA-DD-031202
LEA-DD-030300 Site License extension for OPC Development Toolkits

Scope of Delivery

Software Installation package on Softing OPC Toolkits DVD-ROM, installation package available for download
Support Dedicated Support Team
Documentation Online Help in English in CHM Format as Part of the Installation Package

Additional Products and Services

OPC-ENTW-TAG OPC Engineering / Consulting / Compliance Assistance
TRA-OPC-UA OPC UA Introductory Training for Decision Makers and Technical Leaders
TRA-OPC-UA-DEV OPC UA .NET Developer Training
WRL-DD-031105 OPC UA Model Designer
LRL-DY-134501 dataFEED OPC Suite, Version 4.01 and higher

datacheck analyzer software product bundle for mobile industrial ethernet diagnostics

Analyzer IE & Analyzer PRO

Software for Mobile Diagnostics and Acceptance Testing of Industrial Networks

Analyzer IE / PRO is a comprehensive software solution for acceptance testing and efficient troubleshooting of Ethernet-based industrial communication. In a PROFINET environment, the mobile diagnostic tool generates standardized acceptance reports in accordance with the recommendations of PROFIBUS & PROFINET International (PI), making it an easy-to-use product that is tailored to the needs of plant suppliers, maintenance personnel as well as service providers.

This product belongs to our PROFINET Diagnostics family. In order to view our expertise and the complete list of products please Download the PROFINET Diagnostics Brochure.

Comprehensive Functionality

  • Diagnostics list, error statistics, network statistics
  • Enhanced flexibility by supporting online as well as offline mode
  • Generation, analysis and handling of diagnostic data such as graphical topology, inventory list and reference measurements, also for standard Ethernet components (eg PCs, camera systems)

Automated Generation of Acceptance Test Documents

  • Time saving by automatically created test reports
  • Flexible definition of acceptance criteria
  • Transparent reporting by following PI guidelines

Tool Addressing Complete Plant Lifecycle

  • Data on network configuration, network communication and diagnostic messages
  • Error identification for effective troubleshooting (e.g. based on inventory list of network devices)
  • Chance to support exchange of general project information between end users, EPC contractors, system integrators and maintenance service providers
  • Seamless integration with Softing diagnostics per-manent monitoring solutions TH SCOPE and TH LINK
Technical Data
Functionality
  • Analysis of device logs
  • Live list, statistics, inventory
  • Topology and trend analysis
  • GSDML file support, plaintext messages in diagnostic list
  • Acceptance measurements and acceptance reports
  • Reference comparison
  • Configurable time intervals for automated export of inventory and topology data
  • Data export via Excel
  • Configurable Blacklist feature for robust operation
  • Optional (Analyzer PRO): Telegram analysis: jitter, refresh interval, load ratio
Supported Protocols PROFINET, EtherNet/IP, Modbus TCP
Interfaces
  • SNMP Agent
  • OPC UA Server
System Requirements Adobe Reader 8 or higher for reading the documentation and for printing the topology
Supported Operating Systems Windows 7, Windows 8.1, Windows 10
Windows Server 2012, Windows Server 2012 R2, Windows Server 2016
Network Access Data collection through TH LINK PC (PROFINET, EtherNet/IP, Modbus TCP)
Demo Version Full TH SCOPE functionality can be used for free for 30 days after installation
Licensing Software or hardware key
Scope of Delivery
Software Analyzer IE
License Software key (bound to PC) or hardware key
Hardware profiTap: Network tap for telegram analysis operation, optional (Analyzer PRO)
Documentation Installation manual, user manual, release note
Order Numbers
LRA-JY-003041 Analyzer IE (software key)
LRL-JY-003042 Analyzer IE (hardware key)
KPL-JY-003043 Analyzer PRO
Additional Products and Services
GEA-JN-003006 TH LINK PROFIBUS
GDA-JA-003034 TH LINK PROFINET
GDA-JY-003037 TH LINK Industrial Ethernet
LRA-JY-003028 TH LINK PC Industrial Ethernet
TRA-PB-TECH Training “PROFIBUS Technology”
TRA-PB-TS Training “PROFIBUS Troubleshooting with exam to Certified PROFIBUS Installer”
TRA-PN-CERTINST Training “PROFINET Acceptance and Commissioning”
TRA-PN-CERTENG Training “PROFINET Technology graduated as Certified PROFINET Engineer”
TRA-PN-TOOLS On-site training: PROFINET tools

Please contact us

People interested in this product, may be interested in :

 

Serial Profibus Interface SPI3

Serial Profibus interface : SPI3

  • Coupler for integrating devices with serial interface as DP slave devices in PROFIBUS
  • replaces the serial interface in the PLC in decentralized PROFIBUS installations
  • Suitable for simple applications such as connecting text displays or barcode scanners, as well as for more complex applications such as the integration of identification systems, scales, controllers and laboratory equipment
  • Integration of devices with serial interface as DP slave devices in PROFIBUS networks
  • Available for various protocols and physical Interfaces

Functions

  • DP slave with transmission rate of 9.6 kbit/s up to 12 Mbit/s
  • Serial transmission rate of 110 bit/s up to 57.6 kbit/s (depending on the protocol)
  • Serial interface available as RS 232, RS 422 or RS 485
  • Configuration with GSD file via the PROFIBUS DP master
Nominal supply voltage 24 V DC (19.2 … 28.8)
Current consumption max. 200 mA
Ambient temperature range 0 … +75°F
Transmission rate serial 110 Bit/s up to 57.6 kBit/s (depending on the protocol)
Interface serial RS 232, RS 422, RS 485 (interface as per order)
Protocols serial Free ASCII driver, 3964R, RK512, MODBUS RTU
Transmission rate PROFIBUS 9.6 kBit/s up to 12 MBit/s
Interface PROFIBUS RS 485
IO Range PROFIBUS 2, 4, 8, 16, 32, 64 data words (depending on the protocol)
Case, protection class Plastic, IP 20
Mounting 35 mm DIN top hat rail
Dimensions W x H x D 75 x 75 x 53 mm
Weight 136 g
Certificate CE | UL
GPA-NS-011236 SPI 3 RS 232
GPA-NS-011237 SPI 3 RS 422
GPA-NS-011238 SPI 3 RS 485

Scope of Delivery

SPI 3, Installation Guide
By Download Docu and Media Kit (includes online documentation, GSE, function blocks for SIMATIC S5 and S7, example projects); Release Note

PB-IF-03

PB-IF-03 – Single Channel ISA for PROFIBUS

PROFIboard is an intelligent PC board used to integrate PC-based systems into a PROFIBUS network in a cost effective and easy to use methed.

Applications such as : HMI, SCADA systems, operator interface or PC-based controllers can take advantage of the flexibility and functional completewnesss provided by the various types of Profiboard.

  • Single channel ISA board for Profibus

  • ISA spec compliant

  • 0-55C temperature range

  • Cost Effective and East to Use

  • Supports various protocols

Unit

ISA PC-board, short AT format.

CPU Siemens SAB-C165 Microprocessor
Memory 512-Kbyte Flash, 512 Kbyte SRAM, 16 Kbyte dual port RAM
SUpported PC Interrupts 5,10,11,12,15
Profibus ASIC Siemens ASPC2 and SPC3
Physical Interface Galvanically isolated RS-485

Connector Type

1 x 9 pin Sub-d female
Connector Pinning EN 50 170, part 2 compliant
Hardware Configuration I/O address is set by switch on board; all other settings are software configurable
Power Supply +5 V (+-5%; typ. 700mA
Transfer Rate 9.6KKbit/ up to 12 Mbit/s
Humidity Rating <90% non-condensing
Temperature 0-55C Operating temperature

Reference :  PB-IF-03

This card is phased out.. It might stay some boards on stock.. Please contact us for availabilities